“Just finished installing the Snap’n Lock™ Balusters. It took 2 days to install the framing and balusters. As the title says “It was easy and the balusters are secure. The cost wasn’t bad either.”
– David G., Snap ‘n Lock™ Customer
Snap ‘n Lock™ Baluster Kits come with everything you need to build a rail faster and easier than common plug systems.
(10) Square balusters
(20) Snap ‘n Lock™ square baluster connectors
(20) Screws
Are they strong? Like nothing else you’ve ever seen! In-fill railing sections using Snap ‘n Lock™ Baluster Kits sustained over 4X the code design load!
They’re molded to higher tolerances than a Ferrari engine for precision friction fit locking and made with 100% USA polycarbonate. They’re bulletproof, handle extreme temperatures and are UV protected. Who says we can’t make the best products right here at home!
It’s so simple that even folks who are just starting out can do it themselves with minimal carpentry experience.
| Color Options | Black and White |
| Width Options | 3/4″ balusters |
| Length Options | 25″ Designed for a 36″ rail, 31″ Designed for a 42″ rail |
| Pack Quantity | 10 balusters and 20 Snap’n Lock Connectors and screws |
| Material | Powder coated, extruded aluminum |
| How many do I need? | One kit per 4 linear feet or 2.67 Balusters per lineal foot of railing |
| Warranty | Limited Lifetime |
Screw the base into the 2×4.
Snap in the baluster.
Slide down and lock the collar.
Save time and effort by using our Snap’n Lock Baluster Kits for your next railing.
Whether you’re retro-fitting or starting a new project, they’ll make building your railing a snap, even by yourself.
Do not let the simple look of the Snap ‘n Lock™ Balusters fool you. A lot of thought went into conceiving this design in order to make it work so well. The base and the collar are designed to incredibly tight tolerances so they fit together like a glove and constrict around the baluster to hold it tight eliminating any wobble.
The sidewalls of the base are free to flex and accept the baluster as it is pushed in place. The mating surfaces of the base and the collar are sloped so that as they slide together the fit gets tighter and tighter until they lock together once fully seated.
The parts can be released by fitting a slot screwdriver under the color and popping it up. This allows for easy maintenance or the addition of decorative baluster collars anytime after installation.
Replace old worn 2×2 wood pickets with Snap Lock Balusters without having to dismantle the entire railing.
Sideways installation makes this possible!
With traditional plug systems, you have to take down the entire railing and rebuild from scratch.
Make sure to measure the gap between your upper and lower 2×4 rails and pick the 25″ or 31″ and then cut them down to your specific gap less 1/2″ for the thickness of the base connectors.
Aluminum is so easy to cut and is not subject to oxidization the same way ferrous metals are.
This saves you a lot of time and money. But the best thing is that you just gave your old worn out wood railing a brand new life.
Have you ever had to re-stain your wood railing with the standard baluster connectors? If you have you know how long it takes to painfully and carefully stain around each baluster without leaving a ton of paint on them. This problem is over if you use Snap ‘n Lock® Baluster Connectors. All you do is take a flat screwdriver and pop up the cover so you can stain around the connector shoe with carefree speed. Any overspill with be hidden once you slide the cover back down.
The collar releases using a slot screwdriver.
Stain or paint around the base quickly and easily. No need to use tape.
Just slide and lock the collar down when you are done
Let’s take a closer look at how the stair adapters work with the Snap Lock Balusters connectors.
No need to cut balusters at an angle.
Just snap the adapter to the underside of the base connector and screw the unified parts to the 2×4 as normal.
This helpful visual guide is worth a thousand words and shows just how simple it is.
The shorter 25″ balusters are recommended for most common stair rail applications as shown in the diagram.
The adapters are set at 35 degrees to match the common rise and run for stairs under the residential code.
But sometimes you might have a slightly shorter rise and a longer run. This changes the angle slightly and can differ from the 35-degree default.
Don’t worry. They have enough flex to accommodate stairs from 33 to 38 degrees.
Download a full-size copy of the Warranty.
Linda A.
looks great, no need to paint, ever!
Russell R.
USA: We are a vendor to these dealers. Call these dealers to confirm availability.
Canada: We are a vendor to these dealers. Call these dealers to confirm availability.
Our mission has always been to deliver solutions that look great and perform to higher standards. So we try hard to remove redundant materials, to hide fasteners, and to deliver it all in a form that looks beautiful and stands out from the crowd. It is just one more way we are trying hard to help you succeed.